Dual Fan Spal Brushless Fan Wiring Kit

Dual Fan Spal Brushless Fan Wiring Kit

Two fans. One sensor. No guesswork. Brushless fans do not want a relay slapped on a toggle switch. They want a signal that tells them how hard to work; and most swap wiring never gives them one. This kit does. A temperature sensor reads 175 F at the low end and 195 F at the top. At 175 the fans idle; as coolant climbs the fans climb with it; and at 195 they are pulling their full rated CFM. You get the sensor; the sensor harness and two fan pigtails. That is every connection between the coolant and the fans handled with the right connector on the right end. Add a maxi fuse holder sized to your fans and the cooling side of the build is done. The fans think about the rest.

  • Variable speed; not on and off - the fans ramp with coolant temperature instead of slamming on at a switch point and dragging the alternator with them.
  • Both fans handled - two pigtail harnesses so the second fan is not an afterthought spliced in later.
  • Right connectors on both ends - the sensor harness and pigtails are made for these fans; no butt splices in the hot part of the engine bay.
  • Sized fusing published - 40 amp for 300W fans and 50 amp for 500W fans; the listing tells you what to buy.
  • Quieter at cruise - a fan at minimum speed at 175 F is a fan you stop hearing over the exhaust.

Install Level: Moderate

Temperature sensor range: 175 F to 195 F; variable speed across that range.
A maxi style fuse holder and fuse are required and are not included.
Fuse sizing: 40 amp for 300W fans; 50 amp for 500W fans.
Spal brushless fans are not included.
For a dual fan installation. A single fan setup uses the single fan wiring kit.

Wizard Cooling
SKU: 7-SBL-195KIT-2 ISBN: 7-SBL-195KIT-2
$399.00
Expert Tech Support
ShopTested Parts
Worldwide Shipping
⚠️
WARNING: Handling passenger or off-highway motor vehicle parts can expose you to chemicals such as phthalates and lead. Learn more.
Dual Fan Spal Brushless Fan Wiring Kit
$399.00
Complete your buildThe Next Step for Your Build 
Overview
Specifications
Tech Resources
Compatibility

We're excited to offer this Dual Spal Brushless Fan Wiring Kit with a 195°F sensor. This kit comes with everything you need for your radiator to run how you need; a temperature sensor, temperature sensor harness and two fan pigtail harnesses. For more information, see details below. 

Details

  • Temperature sensor (175°F – 195°F)
  • Temperature sensor harness
  • Fan pigtail harness(QTY:2)

 

Temperature Sensor Range: At the lower temperature the fan will turn on at it’s minimum speed. As temperature increases the fan speed and airflow will increase. At the sensors highest temperature the fan will be on at full speed and will be moving it’s maximum rated CFM.

Wiring Instructions: These kits will require a maxi style fuse holder and fuse. A 40 amp fuse for 300W fans and 50 amp fuse for 500W fans. See Spal's wiring diagram below for instructions on how to wire your kit. 

Wizard Cooling part number 7-SBL-195KIT-2
Vendor: Wizard Cooling
Contents: temperature sensor; temperature sensor harness; two fan pigtail harnesses
Temperature sensor range: 175 F to 195 F
Fan control: variable speed; minimum speed at 175 F rising to full rated CFM at 195 F
Fan count supported: two
Required and not supplied: maxi style fuse holder and fuse
Fuse sizing published: 40 amp for 300W fans; 50 amp for 500W fans
Listed price 399.00 USD
Variant count: 1
No harness length; connector type or sensor thread size is published on this listing
Wires two Spal brushless fans to a 175 F to 195 F temperature sensor.
Tagged for 1953-56; 1957-60; 1961-66; 1967-72 and 1973-79 Ford trucks and 1966-77 and 1978-79 Ford Broncos.
The fans themselves; the maxi fuse holder and the fuse are not included.
A single fan installation uses the single fan wiring kit instead of this one.

SEARCH OUR STORE

Engines, A/C accessories, steering, brakes, & more. Get everything you need for your truck restoration at home.